A Beginner's Guide to Installing a Bathtub
A Beginner's Guide to Installing a Bathtub
Blog Article
Every person may have his or her own perception in relation to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Mounting a tub isn't exactly rocket science, yet it does call for solid plumbing, woodworking, and occasionally, tiling skills. Replacing an old bathtub with a new one is also a reasonably challenging project. If the old tub is readily obtainable, the task can relocate immediately; if you need to open up a wall surface to remove the old tub and also place the brand-new bathtub, the job is a lot harder. In either case, the project is within a residence handyman's abilities, although you will require a helper to leave the old bathtub and also set in the brand-new one. Make sure you have actually certified on your own for the work and also are comfortable attempting it. Rather than working with a professional to take over a halfway-completed job, it is far better to consider using one before you begin. Possibilities are you might need an expert plumber to make tube links.
This write-up will aid you mount a new bath tub in your restroom if you have actually already acquired a new bathtub as well as don't require to transform the plan of your previous water pipes.
Your tools and product checklist need to make up the following:
Planning for the Setup
First of all, the sustaining framework provided with the bathroom needs to be fitted (if called for) according to the maker's directions. Next, fit the taps or mixer to the bathtub. When fitting the tap block, it is essential to ensure that if the tap includes a plastic washer, it is fitted in between the bathroom and the taps. On a plastic bath, it is likewise practical to fit a sustaining plate under the taps device to stop stress on the tub.
Fit the flexible faucet ports to the bottom of both faucets using 2 nuts and also olives (often supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the electrical outlet with the hole in the bath. Use the nut supplied by the supplier to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bathroom. Ensure you use every one of the supplied washers.
Connect the catch to the bottom of the waste outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Link all-time low of the overflow tube in a comparable manner.The bathroom need to now prepare to be suited its last position.
Removing Old Touches
If you need to replace old taps with new ones as a part of your installation, then the first thing you need to do is separate the water system. After doing so, switch on the taps to drain any kind of water staying in the system. The procedure of removing the existing faucets can be quite bothersome because of the restricted gain access to that is frequently the situation.
Use a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that attaches the supply pipelines to the taps. Have a towel prepared for the staying water that will certainly originate from the pipes. When the supply pipes have actually been removed, make use of the exact same tool to loosen the nut that holds the faucets onto the bath/basin. You will need to quit the single faucets from transforming during this procedure. When the taps have actually been eliminated, the holes in the bath/basin will need to be cleaned up of any old sealing substance.
Before moving on to fit the new faucets, contrast the pipeline links on the old taps to the new taps. If the old taps are longer than the brand-new faucets, then a shank adapter is required for the new taps to fit.
Setting up the Bath tub
Utilizing both wooden boards under its feet, position the bath tub in the called for placement. The wooden boards are valuable in evenly spreading out the weight of the bath tub over the area of the boards instead of concentrating all the weight onto 4 small factors.
The following objective is to make sure that the bathtub is leveled all round. This can be attained by examining the spirit level and also adjusting the feet on the bathtub till the level reviews degree.
To set up faucets, fit the bottom of the furthest versatile tap port to the suitable supply pipe by making a compression sign up with; then do the very same for the other faucet.
Switch on the supply of water as well as examine all joints and brand-new pipework for leakages as well as tighten them if essential. Load the tub as well as additionally examine the overflow outlet and the normal outlet for leaks.
Ultimately, deal with the bath paneling as explained in the supplier's instruction manual. Tiling and also sealing around the bathtub must wait up until the bath tub has been made use of a minimum of once as this will settle it right into its last setting.
Fitting New Taps
If the tails of the new faucets are plastic, then you will certainly require a plastic adapter to prevent damage to the thread. One end of the adapter fits on the plastic tail of the tap and also the other end offers a connection to the existent supply pipelines.
If you need to fit a monobloc, after that you will need decreasing couplers, which connects the 10mm pipe of the monobloc to the common 15mm supply pipe.
Next, place the faucet in the placing opening in the bath/basin making sure that the washing machines are in place in between the tap and the sink. Safeguard the tap in place with the supplier offered backnut. As soon as the faucet is securely in position, the supply pipes can be attached to the tails of the taps. The taps can either be linked by using corrugated copper piping or with regular faucet adapters. The previous type ought to be connected to the faucet ends first, tightening only by hand. The supply pipelines can later be attached to the other end. Tighten both ends with a spanner after both ends have been linked.
Tiling Around the Tub
In the location where the bath satisfies the ceramic tile, it is required to seal the joins with a silicone rubber caulking. This is essential as the installation can move sufficient to split a stiff seal, creating the water to permeate the wall in between the bath and also the tiling, bring about issues with wetness and feasible leakages to the ceiling below.
You can select from a selection of coloured sealants to assimilate your fixtures and fittings. They are sold in tubes and also cartridges, and also can sealing gaps approximately a size of 3mm (1/8 inch). If you have a larger space to fill, you can fill it with twists of soaked paper or soft rope. Remember to always load the bath tub with water before sealing, to permit the motion experienced when the tub remains in use. The sealant can break relatively early if you do not take into account this movement prior to sealing.
Conversely, ceramic coving or quadrant floor tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are additionally easily available on the market. It is advisable to fit the floor tiles utilizing waterproof or water-proof sticky as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I came across that piece about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround when doing a lookup on the internet. Sharing is nice. Helping others is fun. Thanks for taking the time to read it.
Seek immediate plumbing assistance now. Report this page